Audio T Verdict
The Rega PS2 is the genuine replacement mains adaptor for compatible Rega products requiring a 24 V AC supply with a maximum output of 100 mA.
It is suitable as a replacement for an original PS2 that has been lost or damaged, or as a spare for compatible equipment. It is a like-for-like replacement rather than a performance upgrade.
Compatibility should always be checked before ordering. The PS2 must not be confused with a generic 24 V DC adaptor or Rega's higher-current PS1 power supply.
Rega PS2 Replacement Power Supply
The Rega PS2 is an official UK replacement power supply designed for selected Rega turntables and compact phono stages.
It accepts a 230 V AC UK mains input and provides a 24 V AC output at up to 100 mA through its fixed low-voltage cable.
The PS2 is intended to replace the original Rega supply specified for the connected product. It does not modify the turntable motor, change playback speed or upgrade the audio circuitry.
Compatible Rega Products
The PS2 is suitable for Rega equipment specifically marked for use with a Rega PS2 or a 24 V AC, 100 mA supply.
Compatible Phono Stages
- Original Rega Fono Mini
-
Rega Fono Mini A2D MK2
- Selected earlier Rega accessories specifically marked for PS2 use
Check Compatibility Before Ordering
Do not select a replacement adaptor from the voltage figure alone. The connected product must require a 24 V AC Rega PS2 with a maximum output of 100 mA and the correct connector.
Contact your local Audio T store
with the Rega product name, approximate age and a photograph of the original adaptor or power input if you need help confirming compatibility.
24 V AC, Not DC
The PS2 provides a 24 V AC output. This is alternating current and is different from the 24 V DC output supplied by many widely available mains adaptors.
A generic adaptor may also have a different connector, current rating or internal arrangement, even when the voltage printed on its case appears similar.
Do Not Use a Generic 24 V DC Adaptor
The Rega PS2 must not be replaced with a conventional 24 V DC power supply.
Using an unsuitable power supply may prevent the product from operating correctly and could cause damage.
PS1 or PS2?
Rega uses more than one type of 24 V AC power supply. The PS1 and PS2 provide the same nominal voltage but have different maximum current ratings and are intended for different products.
Rega PS2
- 24 V AC output
- 100 mA maximum output
- Used with compatible Planar turntables
- Used with the Fono Mini A2D MK2
- This product page
Rega PS1
The
Rega PS1 Replacement Power Supply
provides a higher maximum current output.
- 24 V AC output
- 350 mA maximum output
- Used with the Neo MK2
- Used with compatible Fono MM and Fono MC stages
- Not interchangeable solely because the voltage is the same
Always use the specific supply listed in the Rega manual or printed beside the product's power input.
A Replacement Rather Than an Upgrade
Replacing a correctly functioning PS2 with another PS2 should maintain the intended operation of the connected product rather than change its performance.
It is suitable when:
- The original Rega PS2 has been lost
- The adaptor or cable has been damaged
- A genuine spare power supply is required
- A technician has confirmed that the original supply is faulty
- A correct UK supply is required for compatible Rega equipment
If the Rega product still fails to operate with the correct replacement supply, the connected turntable or phono stage may require inspection.
Connecting the PS2
- Switch off the connected Rega product.
- Disconnect the original power supply from the mains socket.
- Confirm that the product requires a Rega PS2 with a 24 V AC, 100 mA output.
- Insert the PS2 low-voltage plug securely into the product's power input.
- Connect the PS2 to a suitable UK mains socket.
- Switch on the mains supply and operate the connected product normally.
Do not pull the adaptor from the mains socket by its cable or place unnecessary strain on the low-voltage connection.
Positioning and Hum
A mains adaptor can generate an electromagnetic field that may be detected by a turntable cartridge, tonearm cable or sensitive phono-stage circuit.
Position the PS2 as far from the cartridge and audio cables as the fixed lead reasonably allows.
Avoid placing it directly underneath the turntable, beside the cartridge or on top of the Fono Mini.
Safety and Care
- Use the PS2 indoors in a dry location
- Do not expose it to rain, moisture or spilled liquids
- Do not cover the adaptor while it is operating
- Keep it away from radiators and other heat sources
- Do not use it if the casing, mains pins or cable are damaged
- Do not open the casing
- Disconnect it during extended periods of non-use
If the adaptor operates intermittently, becomes unusually hot or produces smoke or an unusual smell, disconnect it from the mains and contact Audio T.
Key Features
- Genuine Rega replacement power supply
- UK mains version
- 24 V AC output
- 100 mA maximum output current
- Compatible with selected Rega turntables
- Compatible with the Rega Fono Mini A2D MK2
- Suitable as a replacement or spare
- Fixed low-voltage output cable
- Like-for-like replacement rather than a performance upgrade
- Lifetime limited warranty against confirmed manufacturing defects
Technical Specifications
- Product type: Replacement external AC power supply
- Mains version: UK
- Input voltage: 230 V AC
- Input frequency: 50 Hz
- Input current: 40 mA
- Output voltage: 24 V AC
- Maximum output current: 100 mA
- Compatibility: Rega products specifically designed for the PS2 supply
Frequently Asked Questions
Is the Rega PS2 output AC or DC?
It provides a 24 V AC output at up to 100 mA. It is not a 24 V DC adaptor.
Can I use a generic 24 V adaptor?
No. Many generic supplies provide DC rather than AC and may also have an unsuitable connector or current rating.
Does it work with the Rega Planar 1?
Yes, where the turntable is designed for the Rega PS2. Check the original supply or manual if the model or age is uncertain.
Does it work with the Rega Planar 2?
Yes. Rega specifies a 24 V AC, 100 mA PS2 for compatible Planar 2 turntables.
Does it work with the Rega Planar 3?
It is suitable for standard Planar 3 models designed for the PS2. The Planar 3 RS uses its supplied Neo MK2 and PS1 arrangement instead.
Does it power the Fono Mini A2D MK2?
Yes. The Fono Mini A2D MK2 is designed for use with the Rega PS2 supply.
Is the PS2 the same as the Rega PS1?
No. Both provide 24 V AC, but the PS2 is rated at 100 mA and the PS1 at 350 mA. Use the supply specified for the connected product.
Will a new PS2 improve sound quality?
It is a like-for-like replacement rather than an upgrade. It should restore normal operation when replacing a missing or faulty original supply.
What should I do if the product still does not work?
Confirm that the correct power supply is connected. If the problem remains, the turntable or phono stage may require inspection.
Can Audio T confirm compatibility?
Yes.
Contact your local Audio T store
with the product name, approximate age and photographs of its power input or original adaptor.
Why Buy From Audio T?
- Genuine Rega replacement product
- Compatibility advice from experienced Rega specialists
- Help distinguishing between Rega PS1 and PS2 supplies
- Support for current and older Rega equipment
- Turntable and phono-stage troubleshooting advice
- Help arranging an inspection if a replacement supply does not resolve the fault
- Ongoing support from the UK's oldest independent specialist Hi-Fi retailer
Contact your local Audio T store
for compatibility advice or help diagnosing a power problem with your Rega product.