Audio T Verdict
The Dynaudio Emit 20 is the larger standmount model in the Emit range, combining a Cerotar soft-dome tweeter with a substantial 18cm MSP mid/bass driver.
Its larger driver and cabinet give it noticeably more bass weight, scale and dynamic ability than the Emit 10, making it well suited to small and medium-sized listening rooms.
The Cerotar tweeter uses Dynaudio’s Hexis inner dome to control resonance, while the long-throw MSP driver uses a copper-clad aluminium voice coil and stacked magnet system for a strong combination of speed and low-frequency authority.
With 86dB sensitivity and a 6-ohm rated impedance, the Emit 20 is compatible with a wide range of quality amplifiers. It is not unusually difficult to drive, but better amplification brings worthwhile improvements in bass control and clarity.
The dual-flared rear port helps the speaker produce convincing bass from a manageable enclosure, although suitable stands and sensible wall clearance remain important.
For customers who want a full-bodied standmount without moving to a floorstanding speaker, the Emit 20 is one of the strongest and most versatile entry points into the Dynaudio range.
Dynaudio Emit 20 Standmount Speakers
The Dynaudio Emit 20 is a passive two-way standmount loudspeaker designed for high-quality stereo systems and multichannel home cinema installations.
Each speaker combines:
- One 28mm Cerotar coated fabric soft-dome tweeter
- Dynaudio’s Hexis resonance-control inner dome
- One 18cm MSP mid/bass driver
- A custom two-way passive crossover
- A dual-flared rear bass-reflex port
- A rigid and internally damped cabinet
- A removable black magnetic grille
- A single pair of loudspeaker terminals
The Emit 20 is supplied as a stereo pair. Suitable speaker stands, amplification and speaker cables are required separately.
The Larger Emit Standmount
The Emit 20 sits above the compact Emit 10 and uses a larger 18cm MSP driver within a more substantial cabinet.
The increased cone area and cabinet volume provide:
- Greater bass extension
- More low-frequency output
- Improved dynamic scale
- Lower cone excursion at a given listening level
- Greater suitability for medium-sized rooms
- More convincing reproduction of larger instruments
It remains compact enough for conventional speaker stands and does not require the floor space of an Emit floorstander.
Designed and Engineered in Denmark
The complete Emit range was developed and tested at Dynaudio Labs in Skanderborg, Denmark.
The speakers are measured in Dynaudio’s Jupiter facility using the same development process applied to the company’s more expensive home and professional products.
The Emit 20 draws on technology developed for ranges including:
- Dynaudio Evoke
- Dynaudio Contour i
- Dynaudio Confidence
- Dynaudio Heritage Special
- Dynaudio Core professional monitors
28mm Cerotar Soft-Dome Tweeter
High frequencies are reproduced by Dynaudio’s 28mm Cerotar coated fabric soft-dome tweeter.
The Cerotar was originally developed for the Evoke range and incorporates technology derived from Dynaudio’s Esotar Forty and professional Esotar Pro tweeters.
Its principal components include:
- A precision-coated fabric diaphragm
- Dynaudio’s Hexis inner dome
- A lightweight aluminium voice coil
- A Ferrite+ ceramic magnet system
- Controlled internal airflow
- A damped cavity behind the diaphragm
The Cerotar is designed to reproduce detail, harmonics and recording ambience while retaining the smooth character associated with Dynaudio’s soft-dome tweeters.
Coated Fabric Diaphragm
The tweeter diaphragm is formed from fabric and treated with a carefully controlled coating.
This construction provides a useful combination of:
- Low moving mass
- Controlled internal damping
- Smooth diaphragm behaviour
- Consistent production
- Reduced dependence on strong resonant peaks
The dome, coating, voice coil, magnet system and rear cavity are engineered to operate as one complete high-frequency assembly.
Hexis Resonance-Control Inner Dome
The Hexis is a small dimpled inner dome positioned immediately behind the Cerotar diaphragm.
Its shape guides airflow behind the soft dome and helps prevent standing waves within the tweeter from reflecting back towards the diaphragm.
Reducing this unwanted internal energy can improve:
- High-frequency smoothness
- Transient control
- Low-level detail
- Decay and ambience
- Integration with the MSP driver
The Hexis concept is also used in Dynaudio’s more expensive Evoke, Contour i and Confidence loudspeakers.
Ferrite+ Ceramic Magnet System
The Cerotar tweeter is driven by a Ferrite+ strontium-carbonate ceramic magnet system.
The motor provides the magnetic force required to move the aluminium voice coil and fabric diaphragm accurately.
Dynaudio selected this magnet system to provide the necessary sensitivity, control, thermal stability and power handling for the Emit range.
Lightweight Aluminium Tweeter Voice Coil
The Cerotar tweeter uses an aluminium voice coil to keep the moving mass low.
A lightweight moving system can respond quickly to small changes in the musical signal while reducing the amount of stored energy within the diaphragm assembly.
The voice coil is designed to work with the dome and magnet system without making the treble sound detached from the larger mid/bass driver.
18cm MSP Mid/Bass Driver
A single 18cm MSP driver reproduces bass and midrange frequencies up to the 3800Hz crossover point.
The driver is based on technology developed for Dynaudio’s Evoke range and incorporates:
- A one-piece MSP cone
- An integrated central dust-cap area
- A copper-clad aluminium voice coil
- A two-layer glass-fibre former
- A stacked ferrite magnet system
- A long-throw suspension
- A substantial rubber surround
- Dynaudio’s balance-rib structure
The driver must reproduce deep bass, vocals and much of the instrumental range, so its motor and suspension need to combine useful excursion with accurate midrange behaviour.
One-Piece MSP Cone
The diaphragm is made from Dynaudio’s Magnesium Silicate Polymer, commonly abbreviated to MSP.
The cone and central dust-cap area are moulded as one continuous piece rather than assembled from separate components.
This construction provides:
- Consistent behaviour across the diaphragm
- Controlled stiffness
- Useful internal damping
- A strong connection to the voice-coil assembly
- No separate dust-cap joint to create another resonance
Dynaudio Balance Ribs
The small ribs visible around the centre of the MSP cone connect the playing surface to the voice-coil assembly behind it.
These balance ribs help the cone and coil operate as one controlled moving system.
The arrangement spreads the motor’s force across the diaphragm and helps maintain the cone’s intended shape as excursion increases.
Copper-Clad Aluminium Voice Coil
The Emit 20 uses copper-clad aluminium voice-coil wire.
This combines an aluminium core with a thin outer layer of copper.
The construction provides:
- Lower moving mass than a solid copper winding
- Improved conductivity compared with bare aluminium
- Space for a greater number of windings
- Strong interaction with the magnet system
- Controlled transient response
The resulting motor provides the force required to control the relatively large 18cm cone.
Two-Layer Glass-Fibre Former
The voice-coil winding is supported by a two-layer glass-fibre former.
The former must remain stable as the cone moves through its available excursion and as temperature changes during prolonged playback.
Glass fibre provides a suitable balance of stiffness, low weight and electrical behaviour.
Stacked Ferrite Magnet System
The 18cm driver uses a stacked ferrite magnet system.
The additional magnetic strength helps maintain control over the voice coil and MSP cone as output and excursion increase.
The motor system supports:
- Improved sensitivity
- Controlled low-frequency movement
- Useful dynamic headroom
- Clear midrange reproduction
- Consistent behaviour at higher listening levels
Long-Throw Driver Suspension
The driver uses a surround and suspension designed to permit substantial controlled cone movement.
This additional excursion helps the Emit 20 produce stronger and deeper bass than the smaller Emit 10.
The suspension must also keep the voice coil centred and return the cone accurately to its resting position after each movement.
Custom Two-Way Crossover
The Emit 20 uses a model-specific passive crossover designed for its Cerotar tweeter, 18cm MSP driver and cabinet.
Dynaudio specifies:
- A 3800Hz crossover frequency
- A first-order electrical topology for the tweeter
- A second-order electrical topology for the mid/bass driver
The crossover was developed by the same engineering team responsible for products including Heritage Special and Dynaudio Core.
First-Order Tweeter Filter
The Cerotar tweeter uses a first-order electrical filter.
A first-order network provides a relatively gentle electrical slope, although the final acoustic response also depends on the tweeter’s natural behaviour, cabinet and interaction with the MSP driver.
The electrical order should therefore not be interpreted as the complete measured acoustic slope.
Second-Order Mid/Bass Filter
The 18cm MSP driver uses a second-order electrical filter through the upper crossover region.
This progressively reduces its output as the Cerotar tweeter takes over above the crossover point.
The different filter orders are selected to achieve the required acoustic integration rather than forcing both drivers to use the same circuit.
3800Hz Crossover Frequency
The MSP driver hands over to the Cerotar tweeter at approximately 3800Hz.
The driver, tweeter, cabinet and crossover must maintain consistent output and phase through this transition so that voices and instruments do not appear to separate between the two units.
The final crossover was refined through measurement and listening at Dynaudio Labs.
Dual-Flared Rear Bass Port
The Emit 20 uses a rear-mounted bass-reflex port that is flared at both its internal and external openings.
The shape allows air to accelerate and decelerate more gradually as it moves through the port.
This helps reduce:
- Air turbulence
- Port compression
- Audible chuffing
- Mechanical noise on deep notes
- Changes in port behaviour at higher output
Rear-Port Positioning
The rear port means that the distance between the speaker and the wall behind it will influence the audible bass balance.
Moving the Emit 20 closer to a wall will normally increase perceived low-frequency output.
Moving it further into the room can improve:
- Bass definition
- Low-frequency timing
- Soundstage depth
- Separation between instruments
- The consistency of individual bass notes
The optimum position will depend on the room, speaker stands, listening seat and partnering amplifier.
53Hz to 25kHz Frequency Response
Dynaudio specifies a frequency response from 53Hz to 25kHz within a +/-3dB tolerance.
At the wider -6dB tolerance, the published response extends from 42Hz to 35kHz.
The difference between these figures demonstrates why a frequency range should always be considered alongside its stated measurement tolerance.
Actual in-room bass will also depend on:
- Distance from nearby walls
- Room dimensions
- Stand height and rigidity
- Listening-seat position
- Amplifier control
- Floor construction
- Low-frequency room modes
Substantial Bass from a Standmount
The Emit 20’s 18cm driver gives it considerably more bass weight and scale than many compact standmount speakers.
It is capable of reproducing convincing body from:
- Bass guitars
- Kick drums
- Piano
- Cello and double bass
- Electronic music
- Film and television soundtracks
Its performance remains subject to the physical limits of a passive two-way standmount, but a subwoofer will not be essential in every stereo system.
Using the Emit 20 Without a Subwoofer
The Emit 20 can provide a satisfying full-range balance in many small and medium-sized rooms without additional bass support.
A subwoofer may still be useful where the system requires:
- Deeper low-frequency extension
- Greater bass weight at quiet listening levels
- Additional headroom for electronic or orchestral music
- Home cinema effects
- More flexibility when managing room modes
Adding the Dynaudio Sub 3
The Dynaudio Sub 3 is a compact active subwoofer suitable for extending an Emit stereo or home cinema system.
Correct integration requires careful adjustment of:
- Subwoofer level
- Crossover frequency
- Phase
- Room position
- Relationship with the main speakers
A correctly adjusted subwoofer should extend the system without becoming obvious as a separate source of bass.
86dB Sensitivity
Dynaudio specifies a sensitivity of 86dB at 2.83V measured at one metre.
This is a moderate figure rather than an especially efficient design.
The required amplifier output will depend on:
- Room size
- Listening distance
- Preferred volume
- Musical dynamics
- Amplifier current delivery
- The required headroom above average listening level
6-Ohm Rated Impedance
The Emit 20 has a rated impedance of 6 ohms.
This makes it a relatively accommodating partner for a broad range of modern integrated and streaming amplifiers.
The amplifier must still provide clean output and remain controlled at the intended listening level.
160W IEC Long-Term Power Handling
Dynaudio specifies IEC long-term power handling of 160W.
This does not mean that a 160W amplifier is compulsory, nor does it guarantee that the speaker cannot be damaged by an amplifier carrying the same rating.
A lower-powered amplifier driven into clipping can produce harmful distortion, while a more powerful amplifier used within sensible limits may provide cleaner dynamic headroom.
Reduce the Volume if the Sound Becomes Distorted
Audible hardness, compression, crackling or obvious distortion can indicate that the amplifier or loudspeakers are being overloaded.
Reduce the volume immediately rather than continuing at the same level.
Amplifier Matching
The Emit 20 can work successfully with a wide range of quality integrated and streaming amplifiers.
Important considerations include:
- Clean power into a 6-ohm loudspeaker load
- Current delivery
- Power-supply capacity
- Bass control
- Room size
- Listening distance
- Preferred playback level
- Source and pre-amplifier quality
A modest amplifier can provide enjoyable results at sensible levels, but the Emit 20 is revealing enough to benefit from higher-quality amplification as the system develops.
The final choice should be established through demonstration rather than comparing headline wattage figures alone.
Browse integrated amplifiers and separates at Audio T to explore suitable options.
Single-Wire Loudspeaker Connections
Each Emit 20 uses one pair of rear loudspeaker terminals.
The speaker is designed for conventional single wiring rather than passive bi-wiring or bi-amping.
The amplifier should always be switched off before speaker cables are connected or removed.
Correct Speaker Polarity
Connect the positive amplifier terminal to the positive speaker terminal and the negative amplifier terminal to the negative speaker terminal.
If one speaker is connected with reversed polarity, the system may lose bass weight, central focus and stereo-image stability even though both speakers continue to produce sound.
The left and right speaker-cable runs should be approximately the same length.
Speaker-Cable Selection
The speaker cable should have sufficiently low resistance for its required length and should be compatible with the partnering amplifier.
Selection should consider:
- Total cable length
- Conductor area
- Amplifier compatibility
- Connector quality
- Installation route
- The overall system budget
Browse speaker cables available from Audio T to compare suitable options.
Speaker Stands Are Essential
The Emit 20 should normally be installed on rigid floor stands rather than placed directly on the floor, a lightweight shelf or resonant furniture.
Suitable stands help provide:
- Correct tweeter height
- A stable mechanical foundation
- Improved stereo imaging
- More consistent bass
- Reduced vibration from nearby furniture
- Greater freedom when positioning the speakers
Speaker Stands Are Not Included
The Emit 20 is supplied as a pair of loudspeakers. Floor stands are required separately unless an individual Audio T package or quotation specifically states otherwise.
Dynaudio Stand 20
The Dynaudio Stand 20 is a suitable Dynaudio support option for the Emit 20.
Its features include:
- A rigid aluminium construction
- A compartment for suitable filling material
- Internal cable management
- Top-adjustable floor spikes
- Rubber rings for hard floors
- Non-slip pads on the top plate
- A wide and stable floor base
Other stands may also be suitable, provided they offer the correct height, stability and top-plate support.
Correct Stand Height
The speaker stand should position the Cerotar tweeter close to the seated listener’s ear height.
A stand that is significantly too high or too low can affect tonal balance and integration around the crossover region.
Both speaker-and-stand assemblies should be level and set to the same height.
Stand Stability and Floor Contact
The complete speaker-and-stand assembly must remain stable on the intended floor.
Carpet spikes can help reach the firm surface beneath a rug or carpet, while rubber contact points or protective discs may be preferable on wood, tile and other sensitive hard floors.
Any filling material should be clean, dry and suitable for the stand manufacturer’s design.
Speaker Positioning
Begin with the Emit 20 speakers positioned symmetrically and with clear space behind their rear ports.
Move both speakers in equal increments while assessing:
- Bass weight
- Bass definition
- Central vocal focus
- Soundstage width
- Soundstage depth
- Image stability
Small changes in wall distance, speaker spacing or listening-seat position can produce worthwhile improvements.
Speaker Spacing
The distance between the speakers should normally be similar to, or slightly less than, the distance from each speaker to the main listening position.
If the pair is positioned too closely, the soundstage may lack width and scale.
If it is positioned too far apart, voices and instruments in the centre can become diffuse or disconnected.
Toe-In and Listening Angle
There is no single toe-in angle that will suit every room.
Greater toe-in can:
- Strengthen central image focus
- Reduce some side-wall reflection
- Create a more direct high-frequency balance
Less toe-in can:
- Broaden the apparent soundstage
- Create a more relaxed tonal balance
- Provide more even coverage across a wider seating area
Both speakers should be adjusted by the same amount.
Using the Emit 20 Close to a Wall
The Emit 20 can be used in a variety of rooms, but its rear port requires more clearance than a completely sealed design.
Where placement close to a wall is unavoidable:
- Keep both speakers at the same distance from the wall
- Avoid placing only one speaker close to a corner
- Keep both port openings unobstructed
- Listen for excessive or uneven bass
- Experiment with small forward movements where possible
Symmetrical Room Placement
Where practical, the immediate surroundings of the left and right speakers should have similar acoustic properties.
Placing one speaker beside heavy curtains and the other beside a bare reflective wall can affect tonal balance and stereo imaging.
Windows, alcoves, open doorways, fireplaces and substantial furniture should all be considered during setup.
Rigid and Internally Damped Cabinet
The Emit 20 cabinet provides a stable mounting platform for the Cerotar tweeter and 18cm MSP driver.
Internal damping is carefully selected for the cabinet volume and bass-reflex tuning.
The enclosure is designed to control:
- Panel vibration
- Internal standing waves
- Rearward energy from the MSP cone
- Unwanted resonance through the midrange
- Colouration from the cabinet structure
Model-Specific Internal Damping
Dynaudio adjusts the quantity and positioning of damping material for each model in the Emit range.
The material absorbs unwanted energy inside the cabinet and reduces reflections returning through the MSP cone.
Too little damping can allow internal resonance to colour the sound, while excessive damping can affect efficiency and bass tuning.
Clean Scandinavian Styling
The Emit 20 uses a clean rectangular form with chamfered front edges and concealed driver fixings.
Its understated design allows it to fit naturally into conventional living rooms, dedicated listening spaces and multichannel installations.
One-piece moulded cover rings conceal the driver mounting screws, with the surface finish embedded into the material rather than applied as a separate lacquer layer.
Current Audio T Finish Options
Audio T currently lists the Emit 20 in:
All three versions use durable custom laminate finishes.
Availability can vary according to current UK stock and production.
Black Magnetic Grilles
Black magnetic grilles are supplied with all three cabinet finishes.
The magnetic attachment avoids visible locating holes when the grilles are removed and allows them to be fitted without tools.
The grilles help protect the Cerotar tweeter and MSP cone from dust and accidental contact.
Never press on the delicate tweeter diaphragm while removing or replacing a grille.
Using the Emit 20 in a Home Cinema System
The Emit 20 can be used as a front, rear or surround-channel speaker within a Dynaudio Emit home cinema system.
The shared Cerotar tweeter and related MSP driver technology help maintain a consistent tonal character across the range.
A complete system may combine:
- Emit 20 front speakers
- Emit 25C centre speaker
- Emit 10 or Emit 20 surround speakers
- Emit 30 or Emit 50 floorstanding front speakers
- A suitable active subwoofer
Matching Emit Front and Centre Speakers
The Dynaudio Emit 25C is the dedicated centre-channel speaker for the Emit range.
It uses the same Cerotar tweeter and related MSP technology, helping voices and effects retain a consistent character as they move across the front soundstage.
AV Receiver Matching
When the Emit 20 is used in a multichannel system, the AV receiver should be selected for the complete speaker arrangement rather than only the front pair.
Important considerations include:
- Power available with several channels operating
- Room size and listening distance
- Speaker crossover settings
- Subwoofer integration
- Required film and music playback levels
- Room-calibration facilities
Browse home cinema amplifiers and AV receivers at Audio T.
Emit 20 or Emit 10?
Choose the Emit 20 When
- Greater bass weight and scale are required
- An 18cm MSP driver suits the room
- The listening space is small to medium in size
- Higher playback levels are expected
- 42Hz extension at -6dB is useful
- The stands can support the larger cabinet
Choose the Emit 10 When
- The room or installation is more restricted
- A smaller cabinet is essential
- The speakers will mainly be used as surrounds
- Moderate listening levels are expected
- The lower purchase price is important
- A 14cm driver provides sufficient scale
The Dynaudio Emit 10 offers the same Cerotar and Hexis tweeter technology within a smaller cabinet with a 14cm MSP driver.
Emit 20 or Emit 30?
Choose the Emit 20 When
- A standmount design is preferred
- A single 18cm driver provides sufficient bass
- The speakers need greater positioning flexibility
- A smaller cabinet is easier to accommodate
- Rigid stands can be positioned correctly
- The lower purchase price better suits the system
Choose the Emit 30 When
- A compact floorstanding speaker is preferred
- Twin 14cm drivers suit the room
- Greater low-frequency output is required
- Separate speaker stands are undesirable
- A medium-sized room is available
- Higher sensitivity is beneficial
The Dynaudio Emit 30 is a compact 2.5-way floorstander using twin 14cm MSP drivers.
Emit 20 or Emit 50?
Choose the Emit 20 When
- A standmount speaker is more appropriate
- The room is small or medium in size
- A simpler two-way design is preferred
- Greater positioning flexibility is useful
- The complete system budget is more limited
- A dedicated midrange is unnecessary
Choose the Emit 50 When
- A large three-way floorstander is required
- Twin 18cm woofers suit the room
- A dedicated midrange driver is preferred
- Greater bass extension and output are required
- Higher cinema playback levels are expected
- The larger cabinet can be positioned correctly
The Dynaudio Emit 50 is the flagship Emit model, combining twin 18cm woofers with a dedicated midrange driver.
Emit 20 or Evoke 20?
Choose the Emit 20 When
- The lower purchase price better suits the system
- A strong entry point into Dynaudio is required
- The laminate finishes suit the room
- The speaker may form part of an Emit cinema system
- The system budget should remain balanced
- The Emit 20 provides the required scale and refinement
Choose the Evoke 20 When
- The step-up Dynaudio standmount is preferred
- A more ambitious cabinet and crossover are required
- Furniture-grade finish options are important
- The amplifier and source justify the additional investment
- Greater overall refinement is the priority
- The higher purchase price suits the complete system
The Dynaudio Evoke 20 is the next step up in Dynaudio’s passive standmount range.
Running-In Period
The Emit 20 can be used immediately after installation, but the driver suspension may continue to loosen and settle with normal playback.
Bass response, integration and overall ease may develop during the first several hours or weeks of use.
Special test signals or continuous high-volume playback are unnecessary. Normal varied music at sensible levels is sufficient.
Cabinet and Driver Care
Clean the cabinet with a soft, dry or very slightly damp cloth.
Do not use:
- Abrasive cleaning products
- Furniture polish
- Solvents
- Aerosol sprays
- Excessive water
Never touch the Cerotar soft dome. Dust on the MSP cone or grille should be removed gently with a clean, soft brush.
Protecting the Finish
Avoid prolonged exposure to direct sunlight, strong uneven artificial light, high humidity or extreme temperature changes.
Keep the speakers away from radiators, open fires and other strong sources of heat.
The custom laminate is durable, but it can still be marked by abrasive cloths, ornaments or repeated contact with hard objects.
System Matching
Well Suited To
- Quality integrated amplifiers
- Streaming amplifiers and network systems
- Vinyl, CD and digital sources
- Small and medium-sized listening rooms
- Listeners wanting substantial bass from a standmount
- Compact television-audio systems
- Dynaudio Emit home cinema systems
- Front, rear or surround-channel use
Check Before Buying
- Suitable speaker stands are included in the budget
- The stands place the tweeters near ear height
- There is sufficient space behind the rear ports
- The amplifier provides adequate clean output
- The room suits the speaker’s bass capability
- The complete stand footprint can be accommodated
- The chosen finish suits the room
- Subwoofer integration has been considered if required
Related Dynaudio Products and Audio T Guides
Key Features
- Powerful passive standmount loudspeaker
- Supplied as a stereo pair
- Designed and engineered at Dynaudio Labs in Denmark
- Two-way driver configuration
- 28mm Cerotar coated fabric soft-dome tweeter
- Dynaudio Hexis resonance-control inner dome
- Ferrite+ ceramic tweeter magnet
- Lightweight aluminium tweeter voice coil
- 18cm MSP mid/bass driver
- One-piece Magnesium Silicate Polymer cone
- Integrated central dust-cap area
- Dynaudio balance-rib construction
- Copper-clad aluminium voice coil
- Two-layer glass-fibre voice-coil former
- Stacked ferrite magnet system
- Long-throw driver suspension
- Model-specific passive crossover
- 3800Hz crossover frequency
- First-order tweeter filter
- Second-order mid/bass filter
- Rear-mounted bass-reflex port
- Dual-flared port design
- Model-specific internal damping
- Concealed driver fixings
- One-piece moulded driver cover rings
- 53Hz to 25kHz response within +/-3dB
- 42Hz to 35kHz response at -6dB
- 86dB sensitivity
- 6-ohm rated impedance
- 160W IEC long-term power handling
- Single-wire loudspeaker connections
- Black magnetic grilles
- Black custom laminate finish
- Walnut custom laminate finish
- White custom laminate finish
- 10.3kg weight per speaker
- Dynaudio Stand 20 compatibility
- Suitable for stereo and home cinema systems
- Suitable for front, rear or surround-channel use
- Up to eight-year total warranty after registration
Frequently Asked Questions
Is the Dynaudio Emit 20 sold as a pair?
Yes. The Audio T product is supplied as a stereo pair.
Are speaker stands included?
No. Suitable floor stands are required separately unless an individual Audio T package or quotation specifically states otherwise.
Which speaker stands are suitable?
The Dynaudio Stand 20 is a suitable option. Other rigid stands can also be considered if they provide an appropriate height, stable base and secure top plate.
Is the Emit 20 a bookshelf speaker?
Dynaudio categorises it as a bookshelf model, but it will normally perform best on rigid floor stands rather than directly on a shelf or lightweight cabinet.
Which tweeter does it use?
A 28mm Cerotar coated fabric soft-dome tweeter with Dynaudio’s Hexis inner dome.
What is the Hexis?
It is a dimpled inner dome positioned behind the tweeter diaphragm to control airflow and reduce unwanted internal resonance.
Which mid/bass driver is fitted?
One 18cm MSP driver with a one-piece cone, copper-clad aluminium voice coil, glass-fibre former and stacked ferrite magnet system.
What does MSP mean?
MSP stands for Magnesium Silicate Polymer, Dynaudio’s proprietary cone material.
What is copper-clad aluminium wire?
It combines a lightweight aluminium core with a thin copper outer layer, improving conductivity without the complete moving mass of a solid copper winding.
What is the crossover frequency?
3800Hz.
What is the crossover topology?
Dynaudio specifies a first-order filter for the tweeter and a second-order filter for the mid/bass driver.
What type of bass port is used?
A rear-mounted bass-reflex port flared at both its internal and external openings.
What is the frequency response?
Dynaudio specifies 53Hz to 25kHz at +/-3dB and 42Hz to 35kHz at -6dB.
What is the sensitivity?
86dB at 2.83V measured at one metre.
What is the rated impedance?
6 ohms.
Is the Emit 20 difficult to drive?
No. Its 6-ohm impedance is relatively accommodating, although its moderate sensitivity means it still benefits from a quality amplifier with clean power and good control.
How much amplifier power is required?
There is no single correct figure. Room size, listening distance, preferred volume, current delivery and amplifier quality all matter.
Does it require a 160W amplifier?
No. The 160W figure is its IEC long-term power-handling specification, not a compulsory amplifier rating.
Can the speakers be bi-wired?
No. Each Emit 20 uses one pair of loudspeaker terminals for conventional single wiring.
How far should the speakers be from the wall?
Begin with clear space behind the rear ports where practical, then move both speakers equally while assessing bass weight and definition.
Can the Emit 20 be placed close to a wall?
Yes, although the wall will normally increase perceived bass output. Keep the ports unobstructed and experiment with small changes in distance.
Should the speakers be toed in?
Experiment with equal toe-in on both channels. The optimum angle depends on the room, listening distance and preferred balance between focus and soundstage width.
Does the Emit 20 require a subwoofer?
Not necessarily. It provides substantial bass for a standmount speaker. A subwoofer can add deeper extension, greater headroom or home cinema impact where required.
Can the Emit 20 be used in a home cinema?
Yes. It can be used for front, rear or surround channels within a Dynaudio Emit multichannel system.
Which centre speaker matches the Emit 20?
The Dynaudio Emit 25C is the dedicated centre-channel speaker for the Emit range.
Are magnetic grilles included?
Yes. Black magnetic grilles are supplied.
Which finishes are available?
Audio T currently lists Black, Walnut and White, subject to availability.
What are the cabinet dimensions?
Dynaudio specifies 205 x 370 x 312mm (W x H x D).
What are the dimensions including the grille?
Dynaudio specifies 205 x 370 x 325mm (W x H x D).
How much does each speaker weigh?
Approximately 10.3kg.
How many speakers are supplied in the box?
Two speakers are supplied as one stereo pair.
What warranty is available?
Dynaudio passive speakers receive the applicable standard legal and manufacturer warranty. Registration within 12 months of purchase can extend total cover to 96 months, subject to Dynaudio’s full terms and proof of purchase.
Why Buy From Audio T?
- Dynaudio Emit 20 demonstrations
- Comparisons with the Emit 10, Emit 30 and Evoke 20
- Amplifier power and system-matching advice
- Comparisons between integrated and streaming amplifiers
- Speaker-stand selection and height guidance
- Dynaudio Stand 20 matching advice
- Room-size and listening-distance assessment
- Speaker positioning, spacing and toe-in setup
- Rear-port and wall-clearance guidance
- Speaker-cable selection and termination
- Dynaudio Sub 3 selection and integration
- Emit 25C home cinema system matching
- AV receiver and surround-system advice
- Finish selection and cabinet-care guidance
- Home demonstrations may be available by arrangement
- Part exchange may be available on suitable existing equipment
- Dynaudio warranty-registration guidance
- Ongoing system, setup and after-sales support
Contact your local Audio T store to arrange a demonstration or discuss amplifier, stand, room, cable and system matching for the Dynaudio Emit 20.